View YB1518_4127459.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

YB1518
Step-up DC-DC Converter White LED Driver Description
The YB1518 is a step-up DC-DC converter; operates as current source to drive up to 6 white LEDs(VIN at 3.0V) or 8 LEDs(VIN at 3.4V) or 9 LEDs(VIN at 3.4V) in series. Series connecting of the LEDs provides identical LED currents resulting in uniform brightness and eliminating the need for ballast resistors. The light intensity of these LEDs is proportional to the current passing through them. The YB1518 switches at a fixed frequency of ~1MHz, allowing the use of tiny, low profile inductors and capacitors to minimize footprint and cost in space consideration applications for cellular phone backlighting or other hand held equipment. The YB1518 can drive up to 9 white LEDs from a single Li-Ion battery. The wide input voltage range from 2.7V to 16V is ideal for portable and automotive (5V/12V) applications with higher conversion efficiency. To control LED brightness, the LED current can be pulsed by applying a PWM (pulse width modulated) signal with a frequency range of 100Hz to 1KHz to the CTRL pin. YB1518 has integrated Latched Over Voltage Protection that prevents damage to the device in case of a high impedance output due to faulty LED or open circuit caused by abnormal conditions.
Features
Built-in internal switch 2.7V to 16V input range <1uA shutdown current High efficiency Internal Soft Start Drives up to 9 white LEDs(VIN at 3.4V) Over voltage protection 36V Small 5-Lead SOT-23 package 100mV Low Reference Voltage
Applications
LCD Display Module White LED Backlighting PDAs, GPS terminals Digital Cameras Cellular Phone Electronic Books Portable Applications
Typical Application Circuit
Figure 1: Typical Application Circuit
YB1518 MRev.1.2
www.yobon.com.tw
1
YB1518
Step-up DC-DC Converter White LED Driver Pin Configuration
Figure 2: YB1518 Pin Configuration
Pin Description
Table 1
Pin 1 2
NAME
Description
SW GND
Switching Pin. This is the collector of the internal NPN power switch. Connect to inductor and diode. Minimize the metal trace area connected to this pin to reduce EMI. Ground Pin. Connect directly to local ground plane. Feedback Pin. Reference voltage is 100mV. Connect LEDs and a resistor at this pin. LED current is determined by the resistance and CTRL voltage. Shutdown Pin and Dimming Control pin. VCTRL > 1.8V generates full-scale LED current VCTRL < 0.4V chip is off Switching from 0.4V to 2.0V, PWM duty cycle controls the LED current Input Supply Pin. Bypass this pin with a capacitor as close to the device as possible
3
FB
4
CTRL
5
VIN
Ordering Information
Table 2
Order Number YB1518ST25
Supplied as 3000 units Tape & Reel
Package Marking Y58M
YB1518 MRev.1.2
www.yobon.com.tw
2
YB1518
Step-up DC-DC Converter White LED Driver Absolute Maximum Ratings
VIN .........................................................................20V SW Voltage ............................................................36V FB Voltage ...............................................................5V CTRL Voltage...........................................................5V Maximum Junction Temp,TJ .............................150C Lead Temperature (Slokering 10 sec) ................300C Thermal Resistance............................................195C
Recommended Operating Conditions
Operating Temperature ............................ -40C~85C Supply Voltage............................................ 2.7 V~16V SW Voltage ............................................................32V
Electricity Characteristics
(TA=25C, Vin=3.3V, Cin=1uF Cout=10uF unless otherwise noted) Table 3 Symbol Vin IQ (Quiescent Current) VFB ICL IB FRSW DTMX DTMN VSAT ILKG Function Parameter Input Voltage Range Not Switching Shutdown Feedback Voltage Switch Current Limit FB Pin Bias Current Switching Frequency Maximum Duty Cycle Minimum Duty Cycle Switch Vcesat Switch Leakage Current VCTRL for Full LED Current CTRL Pin Bias Current Over Voltage Protection Thermal Resistance At Isw = 200mA Ctrl = 0.3V Full On Full Off Ctrl = 2V 40 34 220 1.7 0.3 20 VFB = 0.3V CTRL = 0V Iout=20mA,Vout=12.5V Circuit of Figure 1 100% duty cycle 40% duty cycle VFB=100mV 900 930 90 400 Test Conditions Min 2.7 1.2 1.5 0.3 100 450 350 1 960 85 25 180 1 Typ Max 16 1.7 1 110 Units V mA uA mV mA mA uA KHz % % mV A V V A V C/W
VCTL ICTL OVP JA
Note:
Absolute maximum ratings are limits beyond which damage to the device may occur. The maximum allowable power dissipation is a function of maximum function temperature , TJ(max), the junction to ambient thermal resistance, JA , and the ambient temperature. The maximum allowable, power dissipation at any ambient temperature is calculated using: PD(MAX)= [TJ(max)-TA]/JA . Exceeding the maximum allowable power dissipation will cause excessive die temperature. All limits at temperature extremes are guaranteed via correlation using standard statistical methods YB1518 MRev.1.2
www.yobon.com.tw
3
YB1518
Step-up DC-DC Converter White LED Driver Typical Performance Characteristics
Condition : VIN 2.8V ; 4.4V VOUT ; 2pcs white LEDs / VCRTL : 3V Condition : VIN 2.8V ; 4.4V / VCTRL: 3V VOUT ; 3pcs white LEDs
Efficiency vs Vin (2WLEDs)
82
83.0
Efficiency vs Vin (3WLEDs)
81
82.5
Efficiency(%)
80
Efficiency(%)
2.7 3.0 3.3 3.6 3.9 4.2 4.5
82.0
79
81.5
78
81.0 2.7 3.0 3.3 3.6 3.9 4.2 4.5
Vin(V)
Vin(V)
YB1518 MRev.1.2
www.yobon.com.tw
4
YB1518
Step-up DC-DC Converter White LED Driver
Condition : Vin 2.8V ; 4.4V / Vctrl : 3V VOUT ; 4pcs white LEDs Condition : Vin 2.8V ; 4.4V / Vctrl : 3V VOUT ; 5pcs white LEDs
Efficiency vs Vin (4WLEDs)
83
83
Efficiency vs Vin (5WLEDs)
82
81
81
Efficiency(%)
2.7 3.0 3.3 3.6 3.9 4.2 4.5
Efficiency(%)
79
80
77
79
75 2.7 3.0 3.3 3.6 3.9 4.2 4.5
Vin(V)
Vin(V)
YB1518 MRev.1.2
www.yobon.com.tw
5
YB1518
Step-up DC-DC Converter White LED Driver
Condition : Vin 2.8V ; 4.4V / Vctrl : 3V VOUT ; 6pcs white LEDs Condition : Vin 3.0V ;4.4V / Vctrl : 3V VOUT ; 7pcs white LEDs
Efficiency vs Vin (6WLEDs)
82
Efficiency vs Vin (7WLEDs)
80
80
78
Efficiency(%)
Efficiency(%)
78
76
76
74
74
72
72 2.7 3.0 3.3 3.6 3.9 4.2 4.5
70 2.7 3.0 3.3 3.6 3.9 4.2 4.5
Vin(V)
Vin(V)
YB1518 MRev.1.2
www.yobon.com.tw
6
YB1518
Step-up DC-DC Converter White LED Driver
Condition : Vin 3.0V ; 4.4V / Vctrl : 3V VOUT ; 8pcs white LEDs Condition : Vin 3.4V ; 6.0V / Vctrl : 3V VOUT ; 9pcs white LEDs
Efficiency vs Vin (8WLEDs)
80
Efficiency vs Vin (9WLEDs)
81
78
78
76
Efficiency(%)
Efficiency(%)
75
74
72
72
70 2.7 3.0 3.3 3.6 3.9 4.2 4.5
69 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5
Vin(V)
Vin(V)
YB1518 MRev.1.2
www.yobon.com.tw
7
YB1518
Step-up DC-DC Converter White LED Driver Typical Performance Characteristics
Supply Current (Vctrl = 0V)
1 0.8 0.6 uA 0.4
2 6 5 4
mA 3
Supply Current (Vctrl = Vin)
0.2 0 2 3 4 5 V 6 7 8 9
1 0 2 3 4 5 V 6 7 8 9
Switching Frequency
932.2 932
Vcesat
250 200 Vcesat ( mV) 150 100 50 0
931.8 931.6 Khz 931.4 931.2 931 930.8 2 3 4 5 6 7 8 9 Vin(V)
50
100
150
200
250
300
350
400
Switching Current ( mA)
Switch Leakage Current
0.5 0.4 0.3 uA 0.2 0.1 0 2 3 4 5 6 7 8 9 Vin (V)
60 50 40 uA 30 20 10 0 2 3
CTRL Pin Bias Current
4
5 Vin(V)
6
7
8
9
YB1518 MRev.1.2
www.yobon.com.tw
8
YB1518
Step-up DC-DC Converter White LED Driver Functional Block
Figure 3: YB1518 Block Diagram
Operation
The YB1518 uses a constant frequency, current mode control scheme to regulate the output LED current. Its operation can be understood by referring to the block diagram in Figure 3. At the start of each oscillator cycle, a voltage proportional to the switch current is added to a ramp output and the resulting sum is fed into the positive terminal of the PWM comparator (comparator-1). When this voltage exceeds the level of the comparator negative input, the peak current has been reached, and the SR latch (in Control Logic) is reset and turns off the power switch. The voltage at the negative input of the comparator comes from the output of the error amplifier. The error amplifier sets the correct peak current level to keep the output in regulation. If the error amplifier's output increases, more current is delivered to the output; if it decreases, less current is delivered.
YB1518 MRev.1.2
Application Information
Soft Start and Current Limit The internal soft start circuit minimizes the inrush current during turning on YB1518. The maximum switch current is limited to about 450 mA by the chip. LED Current and Dimming Control The LED's current is set by a resistor connected at FB pin to GND using: 100mV I LED = RLED The maximum LED current set initially can be reduced by pulse width modulating the CTRL. A better approach is to adjust the feedback voltage for dimming control. Either a DC level signal or a filtered PWM signal can be used to control the LED current as illustrated in Figure 4 and Figure
www.yobon.com.tw
9
YB1518
Step-up DC-DC Converter White LED Driver
5 respectively. Using the above different scheme, the LED current can be controlled from 0% to 100% to its maximum value. Duty 0% 20% 30% 40% 50% 60% 70% 80% 100% Iout ( mA) 20 17.4 15 12.4 10 8 6.4 4.07 0
PWM : 2V ; 1KHz ; Vin=3.6V VDC(V)
2 1.8 1.6 1.4 1.2 1 0.8 0.6 0.4 0.2 0
VFB
0 2.2 9.2 19.6 31.1 43.4 63 74 86.4 96.9 102
Iout(mA)
0 0.43 1.8 3.6 6 8.5 12.3 14.5 16.9 19 20
Figure 5. Dimming Control Using a Filtered PWM Signal Over Voltage Protection The YB1518 has an internal over voltage protection circuit which also acts as an open-circuit protection. In the cases of open circuit or the LEDs failure, the LEDs are disconnected from the circuit, and the feedback voltage will be zero. The YB1518 will then switch to a high duty cycle resulting in a high output voltage, which may cause SW pin voltage to exceed its maximum 34V rating. The YB1518 will shutdown automatically until input condition changes to bring it out of the shutdown mode. Inductor Selection A 22uH inductor is recommended for most applications to drive more than 5 LEDs.
Figure 4. Dimming Control Using a DC Voltage
YB1518 MRev.1.2
www.yobon.com.tw
10
YB1518
Step-up DC-DC Converter White LED Driver
Although small size and high efficiency are major concerns, the inductor should have low core losses at 1MHz and low DCR (copper wire resistance). connections for the Cout capacitor can increase the series resistance, which directly effect output voltage ripple. The feedback network, resister R2 should be kept close to the FB pin to minimize copper trace connections that can inject noise into the system. The ground connection for the feedback resistor network should connect directly to an analog ground plane. The analog ground plane should tie directly to the GND pin. If no analog ground plane is available, the ground connection for the feedback network should tie directly to the GND pin. Trace connections made to the inductor and Schottky diode should be minimized to reduce power dissipation and increase overall efficiency.
Diode Selection To maintain high efficiency, the average current rating of the Schottky diode should be large than the peak inductor current, IPK. Schottky diode with a low forward drop and fast switching speeds are ideal for increase efficiency in portable application. Choose a reverse breakdown of the Schottky diode large than the output voltage. Capacitor Selection Choose low ESR capacitors for the output to minimize output voltage ripple. Multilayer capacitors are a good choice for this as well. A 1uF capacitor is sufficient for 2~6 LEDs, 2.2uF is for 7~8 LEDs and 4.7uF is for 9 LEDs applications. For additional bypassing, a 100nF ceramic capacitor can be used to shunt high frequency ripple on the input. The input bypass capacitor Cin, as shown in Figure 1, must be placed close to the IC. This will reduce copper trace resistance which affects input voltage ripple of the IC. For additional input voltage filtering, a 100nF bypass capacitor can be placed in parallel with Cin to shunt any high frequency noise to ground. The output capacitor, Cout, should also be placed close to the IC. Any copper trace
YB1518 MRev.1.2
www.yobon.com.tw
11
YB1518
Step-up DC-DC Converter White LED Driver Package Description
All the contains in this datasheet are not assuming any responsibility for use of any circuitry described no circuit patent license are implied and Yobon reserves the right at any time without notice to change said circuitry and specifications. Yobon Inc. would like to receive your feedback with your recommends and suggestions that is always welcome and with our appreciations.
YB1518 MRev.1.2
www.yobon.com.tw
12

▲Up To Search▲

Price & Availability of YB1518

	To Download YB1518 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .